Meyer Sound SIM 3 Guía de usuario Pagina 206
- Pagina / 232
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
200
CHAPTER 8
SIM 3 Menus
8.5.3. Lobe Study
This mode mutes the loudspeaker system connected to the Live Branch and allows you to
un-mute other systems.
8.5.4. Combined Systems
This mode allows the combination of multiple loudspeakers.
8.5.5. Show
This mode is used when performing SIM 3 measurements during a performance. It prevents
loudspeakers from being accidentally muted, and also disables the Generator.
8.5.6. Mic EQ
This specialized mode is used to measure and adjust the equalization of performance
microphones.
8.5.7. Console Check
This specialized mode is used to test the functions and operating parameters of the mixing
console, including maximum levels, clipping points, harmonic distortion, and gain staging.
The Branch is changed so that the measurement points are the Generator, the Console, and
the Processor.
8.5.8. Mic Compare
This specialized mode is used to compare the reference measurement microphone with
another microphone, and determine any differences in sensitivity and frequency response
between the two. The Branch is changed so that the measurement points are Processor,
Reference Mic, and Branch Mic (the mic being tested).
- USER GUIDE 1
- INTEGRATION TOOLS 1
- Office of Quality Manager 2
- Berkeley, California USA 2
- December 1, 2005 2
- SYMBOLS USED 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- CONTENTS 5
- INTRODUCTION TO THIS MANUAL 7
- CHAPTER 1 10
- SIM 3 Measurement Terminology 10
- 2.1.1.5. Line Inputs 1 and 2 21
- 2.1.1.7. Headphone Output 25
- Device Under Test 26
- CHAPTER 2 27
- The SIM 3 Hardware 27
- 2.1.2.1. AC Connector 28
- 2.2. SIM-3088 LINE SWITCHER 32
- 2.2.1. Front Panel 32
- Bus Select 36
- 2.2.4.2. Audio Connections 39
- 2.3.2. Rear Panel 45
- SIM-3022 Audio Analyzer 46
- 2.4.1. Front Panel 48
- 2.4.2. Rear Panel 48
- 3.1. SETTING UP BRANCHES 57
- 3.1.1. Overview 57
- 3.1.2. Defining Branches 57
- CHAPTER 3 58
- 4.4.1.1. System Requirements 78
- CHAPTER 4 80
- Software Updating 80
- 4.4.2.2. Opening a Project 81
- 4.4.3. Viewing Data 86
- 5.1.3. Console 92
- 5.1.4. Processor 92
- 5.1.5. Microphone 92
- 5.1.6. All 92
- 5.2. LINE SPECTRUM 93
- 5.2.1. Overview 93
- 5.2.3. Console 94
- 5.2.4. Processor 94
- 5.2.5. Microphone 94
- 5.2.6. All 95
- 5.3. DELAY FINDER 95
- 5.3.1. Overview 95
- 5.4. FREQUENCY RESPONSE 99
- 5.4.1. Overview 99
- CHAPTER 5 100
- The Measurements 100
- 5.4.6. Group 101
- 5.4.3. Room 101
- 5.4.4. Processor 101
- 5.4.5. Result 101
- 102
- 6.1. OVERVIEW 103
- 6.2. GRAPH WINDOWS 103
- CHAPTER 6 107
- The SIM Measurement Screen 107
- 6.5. NAMES TAB 111
- 6.6. VALUES TAB 111
- 6.8. DELAYS TAB 115
- 6.9. SPEAKERS TAB 115
- CHAPTER 7 129
- Using SIM 3 129
- 7.2.5. Average Time 132
- 7.2.6. Time Weighting 132
- 7.4.2. Storing Measurements 143
- 7.4.6. Recalling Measurements 147
- 7.4.7. Renaming Measurements 148
- 7.4.8. Sorting Measurements 149
- 7.6.1. Overview 157
- 7.6.3.1. Setup 158
- 7.6.3.3. Delay Finder 158
- 7.7.4. Turning Traces On/Off 160
- 7.7.5. Using Trace Offset 160
- 7.8.1. EQ Overview 164
- 7.10.5. Setting Meter Ranges 171
- 7.12.6. Mic EQ 178
- 7.12.7. Console Check 178
- 7.13. PERFORMING PROCEDURES 180
- 7.13.1. Mic SPL Calibration 180
- 7.13.2. Check Noise 182
- 7.13.3. Check Max Output 182
- 7.13.4. Verify Polarity 182
- 7.13.7. Set System Level 186
- 7.13.8. Set System EQ 187
- 8.1.11. Eject CD 194
- 8.2. VIEW 194
- 8.2.1. View Cursor 194
- 8.2.5. Spectrum Max 196
- 8.2.6. Spectrum Max Hold 196
- 8.2.7. Band Spectrum Solid 197
- 8.2.8. Vertical Zoom 197
- 8.2.9. Horizontal Zoom 197
- 8.2.10. Processor Inverted 198
- 8.2.11. Phase Center at Zero 198
- 8.2.12. Show Coherence as SN 199
- 8.2.13. Smoothing 199
- 8.2.14. Trace Offsets 199
- 8.3. BRANCH 200
- 8.3.1. Edit Branches 200
- 8.3.2. Previous Branch 200
- 8.3.3. Next Branch 201
- 8.3.4. Branch 0 – Branch 32 201
- 8.4. SETTINGS 201
- 8.4.1. Switchers 201
- 8.4.6. Delay Finder Settings 203
- 8.4.8. Input Panel Settings 203
- 8.4.9. Mouse Settings 205
- 8.4.10.Time and Date 205
- 8.5. MODE 205
- 8.5.1. Free Run 205
- 8.5.2. Single System 205
- CHAPTER 8 206
- SIM 3 Menus 206
- 8.7.2. Store DataGroup 209
- 8.7.3. Recall DataGroup 209
- 8.7.4. Clear 209
- 8.7.5. Pause 209
- 8.7.6. Live 210
- 8.7.7. Memory A – Memory D 210
- 8.7.9. Room Offset +/-1 dB 210
- 8.7.10. QuickStore 210
- 8.8. GENERATOR 211
- 8.8.1. Pink Noise (Nz) 211
- 8.8.2. Sine Wave (Sine) 211
- 8.8.3. Pulse (Pls) 211
- 8.9. TABS 211
- 8.10. HELP 213
- 8.10.1. About SIM 3 213
- 8.10.2. Contents 213
- APPENDIX A: SPECIFICATIONS 215
- APPENDIX A 216
- SIM 3 Specifications 216
- APPENDIX B 218
- APPENDIX C 221
- Extended Table of Contents 221
Relacionado con productos y manuales para Cuadernos Meyer Sound SIM 3
Cuadernos Meyer Sound SIM 3 Manual de usuario
(20 paginas)
(20 paginas)
Cuadernos Meyer-sound SIM 3 Manual de usuario
(18 paginas)
(18 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 1.511 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales